DLCC 2026 Security Camera Installation + Equipment

DLCC 2026 Security Camera Installation + Equipment
October 2026
SCOPE: Purchase and install new and replacement cameras and related equipment for the
David L. Lawrence Convention Center. Follow all building rules and ensure labor harmony
during installation. Provide 5-year camera warranties and 1- year labor warranty on all
installations and other equipment. Camera alternates to scope can be specified as alternates,
but please quote camera specified. Please line item each camera section (camera cost,
installation labor, misc.) All work should be completed prior to December 31, 2026. Please
remember that the SEA has MBE/WBE goals. quotes are due November 3, 2026 by 12pm.
There will be a non-mandatory pre-quote meeting and site walkthrough held at the David L.
Lawrence Convention Center at 11AM on Monday, October 26, 2026, meet in the East Lobby of
the Convention Center. Questions for this project must be submitted in writing to Steve Morrison
(procurement@pgh-sea.com) no later than 12pm on October 29, 2026.
For each camera listed below, the successful bidder will be responsible for the purchase and
installation of the indicated camera type, including any new cabling or re-termination of existing
cables being reused. All cabling installed or repurposed in the security rack must be labeled.
The bidder should include any necessary mounting hardware and miscellaneous supplies
needed with each camera, including any needed patch cables (or hi POE injectors.) Each
camera must be programmed with an owner provided IP address, and the view must be
accepted by the owner prior to project completion.
Timeline:
* 10/26/26 11am - Non-mandatory site walkthrough
* 10/29/26 12pm - all questions due
* 10/30/26 - Responses to questions to be issued
* 11/3/26 12pm - Last day to submit quotes
* 11/12/26 - Anticipated Board Approval
1. Purchase Dell Workstation
1. One Workstation (Genetec compatible):
2. 512G SDD drive
3. 64G memory
4. RTX 5070 Ti 16 GB(supporting 3 display port screen w/16 camera HD each)
5. Intel(R) Xeon(R) w5-2465X Processor 3.10 GHz (or better)
6. GbE network interface card
7. Include 5 year hardware warranty
2. Ballroom SE Corner Replacement (Ballroom A c3-03)
Page 1 SEA IManage # 2006494

1. Remove and dispose of exiting Panasonic camera, install new Hanwha XNV-6084R or
approved alternate
2. Provide any mounting hardware changes required, reuse existing cabling
3. Ballroom SW Corner Replacement (Ballroom C - c3-05)
1. Remove and dispose of exiting Panasonic camera, install new Hanwha XNV-6084R or
approved alternate
2. Provide any mounting hardware changes required, reuse existing cabling
4. Ballroom NW Corner Replacement (Ballroom B c3-65)
1. Remove and dispose of exiting Panasonic camera, install new Hanwha XNV-6084R or
approved alternate
2. Provide any mounting hardware changes required, reuse existing cabling
5. East Penthouse Roof exterior new camera installation (2 cameras)
1. Install a Hanwha XNV-6084R and a Hanwha XNV 6084R with appropriate mounting
hardware.
2. Install new cable, conduit and junction boxes as needed.
3. Use a DITEK DTIK-MRJPOES POE surge protector w/ grounding clamp.
4. Purchase two 1 year Genetec camera licenses from Dagastino (our existing Genetec
supplier.)
5. Camera mounting and views must be approved.
6. Existing cable can be jacked in line (in a junction box,) or used as a pull cable.
Terminate ends.
6. West Penthouse Roof exterior new camera installation (2 cameras)
1. Install a Hanwha XNV-6084R and a Hanwha XNV 6084R with appropriate mounting
hardware.
2. Install new cable, conduit and junction boxes as needed.
3. Use a DITEK DTIK-MRJPOES POE surge protector w/ grounding clamp.
4. Purchase two 1 year Genetec camera licenses from Dagastino (our existing Genetec
supplier.)
5. Camera mounting and views must be approved.
6. Existing cable can be jacked in line (in a junction box,) or used as a pull cable.
Terminate ends.
ADD/ALTERNATES:
A1. PE1 Garage Elevator vestibule 180
1. Demo existing camera facing elevator lobby (cam xx.)
2. Relocate existing junction box 4in to improve view
3. Install new Hanwha PNM-A13022RV
Page 2 SEA IManage # 2006494

4. Install flex duct as needed.
5. Re-purpose existing cable
6. New camera to capture elevator lobby and pay stations.
A2. Ballroom Service corridor Dual Head
1. Re-use existing location and cable. (relocate 15 ft west if existing cabling allows)
2. Install new Hanwha PNM-A13022RV
3. Provide any mounting hardware required
4. New camera views North and South hallway.
A3. Levy Service corridor 180
1. Re-use existing location and cable. (relocate 15 ft west if existing cabling allows)
2. Install new Hanwha PNM-A13022RV
3. Provide any mounting hardware required
4. New camera views North and South hallway.
A4. 3rd Floor NE Service corridor Dual Head
1. Re-use existing location and cable
2. Install new Hanwha PNM-A13022RV
3. Provide any mounting hardware required
4. New camera views North and South hallway.
A5. 3rd Floor NW Service corridor Dual Head
1. Re-use existing location and cable.
2. Install new Hanwha PNM-A13022RV
3. Provide any mounting hardware required
4. New camera views North and South hallway.
Page 3 SEA IManage # 2006494