Wastewater Rotors
| Location: | Missouri |
|---|---|
| Posted: | Dec 2, 2025 |
| Due: | Dec 30, 2025 |
| Agency: | Neosho city |
| Type of Government: | State & Local |
| Category: |
|
| Publication URL: | To access bid details, please log in. |
| Bid Title: |
Wastewater Rotors
|
| Category: | Administration |
| Status: | Open |
|
Attachment Preview
City of Neosho
203 E. Main St.
Neosho, MO 64850
(417) 451-8050 phone
(417) 451-8065 fax
www.neoshomo.GOV
INSTRUCTIONS TO BIDDERS
The City of Neosho, Missouri will accept sealed bids until Tuesday, December 30, 2025 at 10:00 am
at the Receptionist Desk of City Hall, Attn: City Clerk, 203 East Main Street, Neosho, MO 64850.
The bid will be for the following:
Project: Wastewater Rotors
Please label the envelope: Wastewater Rotors bid opening Tuesday , December 30, 2025 at
10:00 a.m.
Questions concerning the specifications and bid procedure should be directed to Ken Brady @ 15318
Kentucky Road, 417-451-8075 or Jerry Humphrey @ 2201 Scenic Drive, 417-451-8075, Neosho,
MO.
All bids shall be F.O.B., Neosho, MO. All bids shall be exclusive of federal, state, and city taxes.
Bids on this (these) unit(s) shall be made on forms furnished with these specifications. Additional
information, specifications, deviations, and manufacturer’s literature should be attached to bid forms.
All bids should include the turnaround time in getting started on this project.
*W-9 Required
The City reserves the right to reject any or all bids and to accept the lowest or best bid. The City
reserves the right to split bids, if in the best interest of the City.
Thank you,
David Kennedy
City Manager
BID SPECIFICATIONS:
The bid packet is for the purchase of: (Bid each Rotor Separately)
ROTOR #1 - REPAIRS
• Remove from ditch.
• Remove fins from tube, clean and inspect for reuse, replace as needed.
• Remove flanges from tube, clean and machine as needed for reuse.
• Check shafts for trueness.
• New 50HP Electric motor.
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard
Motor Mount Belt Guard.
• Sandblast tube, flanges and deflector plates
• Prime and paint tube, flanges and deflector plates with 2-part paint with hardener
• Replace (Rexnord) pillow block bearings
• Replace seals
• Replace belts.
• Reinstall at facility.
• If shafts, tubes, or fins and flanges need to be replaced include in bid
ROTOR #3 – TOTAL REBUILD
• Remove from ditch.
• Remove fins from tube, clean and inspect for reuse, replace as needed.
• Remove flanges from tube, clean and machine as needed for reuse.
• Replace shafts.
• New 50HP Electric motor.
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard Motor
Mount Belt Guard.
• New tube.
• Drill and tap for studs to mount fins.
• Replace deflector plates.
• Sandblast tube, flanges and deflector plates
• Prime and paint tube, flanges and deflector plates with 2-part paint with hardener
• Replace (Rexnord) pillow block bearings
• Replace seals
• Replace belts.
• Reinstall at facility
• If new fins or flanges are need include in the bid
ROTOR #4 – TOTAL REBUILD
• Remove from ditch.
• Remove fins from tube, clean and inspect for reuse, replace as needed.
• Remove flanges from tube, clean and machine as needed for reuse.
• Replace shafts.
• New 50HP Electric motor.
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard Motor
Mount Belt Guard.
• New tube.
• Drill and tap for studs to mount fins.
• Replace deflector plates.
• Sandblast tube, flanges and deflector plates
• Prime and paint tube, flanges and deflector plates with 2-part paint with hardener
• Replace (Rexnord) pillow block bearings
• Replace seals Replace at facility.belts.
• If new fins or flanges are needed include in bid.
ROTOR #5 - REPAIRS
• Remove from ditch.
• Remove fins from tube, clean and inspect for reuse, replace as needed.
• Remove flanges from tube, clean and machine as needed for reuse.
• New shafts.
• New 50HP Electric motor.
• New turn buckle for motor.
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard
Motor Mount Belt Guard.
• Sandblast tube, flanges and deflector plates
• Prime and paint tube, flanges and deflector plates with 2-part paint with hardener
• Replace (Rexnord) pillow block bearings
• Replace seals
• Replace belts.
• Replace wall plate.
• Reinstall at facility.
• If new fins or flanges are needed
include in bid
ROTOR #6 - REPAIRS
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard
Motor Mount Belt Guard.
• Replace (Rexnord) pillow block bearings
• Replace seals
• Replace belts.
• Replace terminal box for motor.
ROTOR #7 – TOTAL REBUILD
• Remove from ditch.
• Remove fins from broken tube, clean and inspect for reuse, replace as needed.
• Remove flanges from broken tube, clean and machine as needed for reuse.
• Replace shafts.
• New 50HP Electric motor.
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard Motor
Mount Belt Guard.
• New tube.
• Drill and tap for studs to mount fins.
• Replace deflector plates.
• Sandblast tube, flanges and deflector plates
• Prime and paint tube, flanges and deflector plates with 2-part paint with hardener
• Replace (Rexnord) pillow block bearings
• Replace seals .
• Replace belts.
• Reinstall at facility.
• If new fins or flanges are needed
include in bid
ROTOR # 8 – TOTAL REBUILD
• Remove from ditch.
• Remove fins from broken tube, clean and inspect for reuse, replace as needed.
• Remove flanges from broken tube, clean and machine as needed for reuse.
• Replace shafts.
• New 50HP Electric motor.
• New Baldor Dodge Reducer, Bushing Assembly, Motor Mount Assembly and Standard Motor
Mount Belt Guard.
• New tube.
• Drill and tap for studs to mount fins.
• Replace deflector plates.
• Sandblast tube, flanges and deflector plates
• Prime and paint tube, flanges and deflector plates with 2-part paint with hardener
• Replace (Rexnord) pillow block bearings
• Replace seals
• Replace belts.
• Reinstall at facility.
Equipment Schedule:
Note:
This bid should include a start date for these.
BID FORM
Description: (To be completed by bidding party)
Price(s) for unit(s) meeting enclosed specifications:
F.O.B. Neosho, MO
Projected Shipping Date:
After delivery - payment made on third Tuesday of month delivered
I certify that this bid on stated piece(s) of equipment meets or exceeds the bid specifications (unless
otherwise noted).
COMPANY:
ADDRESS:
PHONE:
EMAIL:
BY:
_______
_______
_______
This is the opportunity summary page. It provides an overview of this opportunity and a preview of the attached documentation.
Daily notification on new contract opportunities
With GovernmentContracts, you can:
- Find more opportunities and win more business
- Receive daily alerts for all new bid opportunities
- Get contract opportunities matched to your business
See also
...Wastewater Treatment Improvements - City of Wakefield, KS 23-1208 StatusAccepting Bids Prebid Date... ...
Drexel Technologies
Bid Due: 6/30/2026
...Wastewater Treatment Improvements - City of Wakefield, KS 23-1208 StatusAccepting Bids Prebid Date... ...
Drexel Technologies
Bid Due: 6/30/2026
...Wastewater Treatment Improvements - City of Wakefield, KS 23-1208 StatusAccepting Bids Prebid Date... ...
Drexel Technologies
Bid Due: 6/30/2026
...Project Description: The City of Jefferson, Public Works, Wastewater Department, herein referred... sampling ...
City of Jefferson
Bid Due: 6/18/2026
* Disclaimer: Information regarding bids, requests for proposals (RFPs), or requests for qualifications (RFQs) is provided on this website only for convenience and does not constitute official public notice. Persons wishing to respond to or inquire about bids, RFPs, or RFQs should contact the appropriate government department.