HWSF Support Supplies

Oil Filter Crusher- High Capacity Truck, Heavy Equipment, Industrial Oil Filter Crusher. This model is the largest vertically oriented crusher. It is built to accommodate large, industrial oil filters up to 20″ tall or multiple truck oil filters. This is the model of choice for high volume generators of heavy-duty truck oil filters. This model also crushes 5-gallon paint cans. Electric/hydraulic – requires no shop air, is very quiet, and provides consistent crushing force, Legs accommodate two 55-gallon drums directly under the machine – one to catch the crushed oil filters, the other for the waste oil, Large crushing chamber and over 70,000 lbs. of force allows thorough crushing of multiple truck oil filters saving on labor time. Overall height is 104”, Overall width is 36”, Overall Depth is 60”, Shipping Weight is 1500 lbs. Cycle Time is 57 seconds, Cavity Size is 15”w x 15”d x 20”h, Electrical-208-230v., 15 amp., single phase, Crushing Force is 70,650 lbs.

52” Heavy Duty Rotary Broom- Clean everything from dirt and leaves or even 2-inches of snow with this versatile broom. Angle broom from 0-27 degrees, right or left. Choose from 9-different sweeping height positions, in .5-in. increments. Attach broom in minutes, no tools needed, with the required front Quick-Hitch system. The 52-in. (132-cm) wide brush section is assembled with 22 convoluted polypropylene wafers. The wafer bristles' convoluted design provides good flicking action. It is recommended all 22 wafers be replaced at the same time for even wear. The 52-in. (132-cm) Rotary Broom increases tractor versatility by allowing it to be used for a variety of sweeping jobs. The broom effectively meets the needs of commercial, farm, home, and estate operators with four-season versatility:

Spring: The broom can be used to dethatch lawns, and it cleans off tennis courts quickly and effectively.

Summer: The broom effectively performs a wide variety of sweeping jobs, including cleaning sidewalks, parking lots, driveways, construction job sites, and barns. It can also be used for backfilling trenches.

Fall: The broom can be used to sweep leaves and windrow pine needles. It sweeps artificial turf and cleans up spectator areas after sporting events.

Winter: It effectively moves up to 2 in. (5 cm) of snow, which may eliminate the need for a snow thrower, depending on the operator's geographic area.

A center chain drive provides dependable power to the broom head: Large, number 50 roller chain is durable and dependable. Offset 3-to-1 reduction gearbox transfers power from the drive shaft to the roller chain drive. Shear bolts are provided at the outer ends of each half of the broom and also on the power take-off (PTO) drive shaft to protect against damage: Shear bolts protect the broom and drive system from damage, if an abrupt impact occurs. Three spare bolts for the drive shaft are provided in storage holes located at the rear of the housing. Left- and right-rear caster wheels are standard equipment: Provide support to the brush head for optimum ground contact. Measure 6.25 in. (16 cm) x 3.25 in. (8 cm). Adjustable by 2 in. (5 cm), with four 0.5-in. (1-cm) spacers. Easy maintenance for long life through grease fittings

Quick-Hitch System- The front Quick-Hitch slips over and locks onto the frame with attached snap pins. It permits quick and easy installation and control of front equipment. Hydraulics are used to raise the hitch into the implement mounting points, then locking in place with the snap pins. No tools are required. There are no loose parts to find. The same hitch works with a front blade, rotary broom, or snow blower. The hydraulic angling kit is required for some front Quick-Hitch-mounted implements. Drive parts are required to operate snow blowers and rotary brooms.

Trailer-Tilt Bed Trailer - 16' Tilt, 6' Stationary, Spare tire, Payload capacity of 16,000lbs, Over-all width: 8 ft. 6 in. (approx.), Height 23 in. (minimum loaded height), 12" x 12" x 48" toolbox, Hitch: standard GN 2-5/16" (25,000 lb) with a gooseneck length of 8'8", 5 x 5 x 5/16" Angle Frame Upper Frame, Expanded metal traction strips, 8" x 2" x 3/8" Tube Frame for Lower Frame, Expanded metal welded on beavertail for traction, 5" Tall Solid Front Rail --Flush Floor