| MOUNTING HEIGHT SCHEDULE |
|
| *SWITCHES |
4'-0" |
| *RECEPTACLES |
1'-6" |
| *WEATHERPROOF RECEPTACLES |
2'-0" |
| BRANCH PANELS (TOP) |
6'-6" |
| DISCONNECT SWITCHES (TOP) |
5'-6" |
| MOUNTING HEIGHTS SHALL PREVAIL ON ALL NEW CONSTRUCTION
UNLESS OTHERWISE NOTED.
MOUNTING HEIGHTS ARE TO CENTER OF DEVICE AND ABOVE
FINISHED FLOOR UNLESS OTHERWISE NOTED.
COORDINATE FINAL MOUNTING HEIGHTS FOR DEVICES ABOVE
COUNTERS WITH ARCHITECTURAL ELEVATIONS.
COORDINATE FINAL MOUNTING HEIGHTS FOR DEVICES FOR
EQUIPMENT WITH ARCHITECTURAL ELEVATIONS.
MOUNTING FOR DEVICES SHOWN ABOVE BASEBOARD HEATERS, 4"
ABOVE HEATER, MOUNTED VERTICALLY.
THESE ARE TYPICAL MOUNTING HEIGHTS. NOT ALL DEVICES ARE
NECESSARILY APPLICABLE TO THIS PROJECT.
*MOUNTING HEIGHTS COMPLY WITH ICC/ANSI A117.1-09 |
|
| REVISION SCHEDULE |
|
| # DESCRIPT |
ION DATE |
|
|
0"
1"
REVISION SCHEDULE
# DESCRIPTION DATE
SHEET NAME
SHEET NO.
CLLAKSALA
3T
gnireenignE
lacirtcelE
&
lacinahceM
001
etiuS
,truoC
atsilaC
103
81599
KA
,egarohcnA
5797-568-709
:xaF
0097-568-709
:hP
CERTIFICATE OF AUTHORIZATION NO:
T3 ALASKA, LLC AECL #: 1625
JOB NO. 2025.119.0
DATE 2026.01.16
DRAWN
REVIEWED
HALF SCALE WHEN PRINTED AT 11x17
YTIROHTUA
GNISUOH
TELNI
KOOC
SNOITAVONER
EZTIANEK
AKSALA
,EGAROHCNA
ELECTRICAL SYMBOLS
SAMANTHA V. REDICK
LIGHTING FIXTURES POWER DEVICES AND EQUIPMENT
SURFACE LIGHT FIXTURE DUPLEX RECEPTACLE / QUADRAPLEX RECEPTACLE
R E G
ISTEREDP
E
0
R
E
1
O
-
/
1
F
1
E
1
5
S
7
/
S
2
9
I
6
O
8
N
7
AL
ENGI
NE E R
RECESSED LIGHT FIXTURE DUPLEX / QUADRAPLEX ABOVE COUNTER RECEPTACLE
EMERGENCY LIGHT FIXTURE GFCI PROTECTED RECEPTACLE
PROJECT DESCRIPTION
WALL LIGHT FIXTURE - LINEAR AC GFCI PROTECTED ABOVE COUNTER RECEPTACLE
STRIP LIGHT FIXTURE SPLIT WIRED RECEPTACLE
DESIGN INTENT IS TO REPLACE EXISTING LIGHTING FIXTURES, DEVICES,
AND COVER PLATES SHOWN ON A ONE-FOR-ONE BASIS WITH NEW LED TYPE
RECESSED CAN LIGHT FIXTURE SIMPLEX RECEPTACLE
FIXTURES. CIRCUIT BREAKERS SERVING UNITS SHALL ALSO BE REPLACED
SURFACE LIGHT FIXTURE SPECIAL PURPOSE RECEPTACLE, 3 & 1 AS NOTED WITH NEW, PROVIDE ARC FAULT AND GFCI TYPE AS INDICATED.
PENDANT LIGHT FIXTURE A DUPLEX SMALL APPLIANCE RECEPTACLE
ALL EQUIPMENT PROVIDED SHALL COMPLY WITH THE BUY AMERICA ACT, 41
USC CHAPTER 83. CONFIRM COMPLIANCE WITH EQUIPMENT/DEVICE
TRACK LIGHT FIXTURE HEAD D DRYER RECEPTACLE, NEMA 14-30R
MANUFACTURER PRIOR TO PROCUREMENT.
WALL LIGHT FIXTURE R ELECTRIC RANGE RECEPTACLE, NEMA 14-50R
SELF CONTAINED EMERGENCY LIGHT FLOOR MOUNTED DEVICE (RECEPTACLE SHOWN)
ELECTRICAL ABBREVIATIONS
EMERGENCY LIGHT - SINGLE HEAD CEILING MOUNTED DEVICE (RECEPTACLE SHOWN)
EXIT LIGHT - WALL MOUNTED POWER RECEPTACLE DROP
AC ABOVE COUNTER
EXIT LIGHT - CEILING MOUNTED J JUNCTION BOX AFF ABOVE FINISHED FLOOR
AFCI ARC FAULT CIRCUIT INTERRUPTER
EXIT LIGHT DIRECTIONAL ARROWS ELECTRIC MOTOR
AIC AMPERES INTERRUPTING CAPACITY
FAN & LIGHT COMBINATION T ELECTRIC MOTOR WITH STARTER SWITCH AMP, A AMPERE
ARCH ARCHITECTURAL
POLE MOUNTED AREA LIGHT FIXTURE EF EXHAUST FAN AWG AMERICAN WIRE GAUGE
C CONDUIT
FLOOD LIGHT UH UNIT HEATER degreesC CELSIUS
CB CIRCUIT BREAKER
WALL MOUNTED AREA LIGHT FIXTURE CH CABINET UNIT HEATER CKT CIRCUIT
CLG CEILING
CEILING MOUNTED FAN FLUSH MOUNT ELECTRICAL PANEL - 208V & 480V
CO CONDUIT ONLY
COMM COMMUNICATIONS
SURFACE MOUNT ELECTRICAL PANEL - 208V & 480V
LIGHTING CONTROLS EF EXHAUST FAN
E,Ex, EXIST EXISTING
NON-FUSED DISCONNECT SWITCH
SINGLE POLE SWITCH EM EMERGENCY
FUSED DISCONNECT SWITCH EMT ELECTRICAL METALLIC TUBING
D DIMMER SWITCH FA FIRE ALARM
COMBINATION MOTOR/STARTER DISCONNECT SWITCH FACP FIRE ALARM CONTROL PANEL
O OCCUPANCY SENSOR SWITCH FLA FULL LOAD AMPS
V VFD DISCONNECT
G, GRD GROUND
3 4 THREE & FOUR WAY SWITCH
GFCI GROUND FAULT CURRENT INTERRUPTER PB AC PUSH BUTTON OR ACCESS CONTROL JUNCTION BOX
K KEY OPERATED SWITCH GF GROUND FAULT PROTECTION
PB AC PUSH BUTTON OR ACCESS CONTROL BOX HP HORSE POWER
PC PHOTOCELL IN, " INCHES
J TRAFFIC CONTROL JUNCTION BOX K DEGREE KELVIN
M M MOTION SENSOR (WALL & CEILING) KCMIL, MCM THOUSAND CIRCULAR MILS
MF MF WALL / FLOOR MOUNTED MODULAR FURNITURE POWER KVA KILOVOLT AMPERES
OS OS OCCUPANCY SENSOR (WALL & CEILING) W F
KW KILOWATT
TELECOMMUNICATION DEVICES MAX MAXIMUM
CONDUITS AND CONDUCTORS MCB MAIN CIRCUIT BREAKER
MECH MECHANICAL
TELECOMMUNICATIONS OUTLET
CONDUIT OR CABLE, CONCEALED U.N.O. MLO MAIN LUGS ONLY
#10 TELEPHONE (VOICE) OUTLET N NEUTRAL
NUMBER AND SIZE OF WIRES NC NORMALLY CLOSED
(NO SLASHES INDICATES 3#12) FLOOR MOUNTED DEVICE (TELECOMM SHOWN) NEC NATIONAL ELECTRIC CODE
NIC NOT IN CONTRACT
CONDUIT HOMERUN TO PANEL CEILING MOUNTED DEVICE (TELECOMM SHOWN) NO., # NUMBER
P-#
(PANEL & CIRCUIT NUMBER) PA PUBLIC ADDRESS
S S SPEAKER (WALL & CEILING) PH, PHASE
RECPT, REC RECEPTACLE
LIGHT FIXTURE NOMENCLATURE TTVV TV TELEVISION OUTLET (WALL & CEILING) REQ, REQD REQUIRED
Re RELOCATED
TD TD TELEVISION/DATA COMBO OUTLET (WALL & CEILING)
FIXTURE TYPE PER SCHEDULE TELECOM TELECOMMUNICATIONS
TV TELEVISION
ASSOCIATED SWITCH OR CONTROL ZONE DC CLOCK (DIGITAL & ANALOG)
TYP TYPICAL
(NO ID = CONTROL VIA SINGLE ROOM SWITCH)
UC UNDER COUNTER
A a (nl = NIGHT LIGHT) S CLOCK & SPEAKER COMBINATION
P- ## UG UNDERGROUND
OP OVERHEAD PROJECTOR UON UNLESS OTHERWISE NOTED
PANEL & CIRCUIT #
UPS UNINTERRUPTIBLE POWER SUPPLY
SECURITY SYSTEM DEVICES
UTP UNSHIELDED TWISTED PAIR
FIRE ALARM DEVICES V VOLTS
VA VOLT AMPERES
AC INTERCOM / ACCESS CONTROL MASTER STATION
FAP FIRE ALARM PANEL VFD VARIABLE FREQUENCY DRIVE
W WATT
IC INTERCOM / ACCESS CONTROL DOOR ENTRY STATION
HEAT DETECTOR (FIXED TEMP. AS NOTED) WP WEATHERPROOF
135o
ES ACCESS CONTROL ELECTRIC STRIKE/LOCK
SMOKE DETECTOR
PS POWER SUPPLY
SMOKE/CO DETECTOR COMBO MOUNTING HEIGHT SCHEDULE
CO
HORN DOOR CHIME *SWITCHES 4'-0"
*RECEPTACLES 1'-6"
KEYPAD
HORN & STROBE *WEATHERPROOF RECEPTACLES 2'-0"
CR CARD READER BRANCH PANELS (TOP) 6'-6"
STROBE
DISCONNECT SWITCHES (TOP) 5'-6"
GB GLASS BREAK SENSOR
FIRE ALARM PULL STATION
MOUNTING HEIGHTS SHALL PREVAIL ON ALL NEW CONSTRUCTION
SURVEILLANCE CAMERA UNLESS OTHERWISE NOTED.
M MAGNETIC DOOR HOLDER
VARIABLE DIRECTION SURVEILLANCE CAMERA
FS FIRE SMOKE DAMPER MOUNTING HEIGHTS ARE TO CENTER OF DEVICE AND ABOVE
FINISHED FLOOR UNLESS OTHERWISE NOTED.
DOOR BELL BUTTON
GENERAL
COORDINATE FINAL MOUNTING HEIGHTS FOR DEVICES ABOVE
COUNTERS WITH ARCHITECTURAL ELEVATIONS.
DASHED SYMBOL = DEVICE TO BE REMOVED
COORDINATE FINAL MOUNTING HEIGHTS FOR DEVICES FOR
DASHED LINE = EQUIPEMENT TO BE REMOVED
EQUIPMENT WITH ARCHITECTURAL ELEVATIONS.
SVR MOUNTING FOR DEVICES SHOWN ABOVE BASEBOARD HEATERS, 4"
TCA ABOVE HEATER, MOUNTED VERTICALLY.
THESE ARE TYPICAL MOUNTING HEIGHTS. NOT ALL DEVICES ARE
NECESSARILY APPLICABLE TO THIS PROJECT. ABBREVIATIONS & LEGENDS,
*MOUNTING HEIGHTS COMPLY WITH ICC/ANSI A117.1-09
E0.01
PERMIT DOCUMENTS
| REVISION SCHEDULE |
|
| # DESCRIPT |
ION DATE |
|
|
0"
1"
REVISION SCHEDULE
# DESCRIPTION DATE
SHEET NAME
SHEET NO.
CLLAKSALA
3T
gnireenignE
lacirtcelE
&
lacinahceM
001
etiuS
,truoC
atsilaC
103
81599
KA
,egarohcnA
5797-568-709
:xaF
0097-568-709
:hP
CERTIFICATE OF AUTHORIZATION NO:
T3 ALASKA, LLC AECL #: 1625
JOB NO. 2025.119.0
DATE 2026.01.16
DRAWN
REVIEWED
HALF SCALE WHEN PRINTED AT 11x17
YTIROHTUA
GNISUOH
TELNI
KOOC
SNOITAVONER
EZTIANEK
AKSALA
,EGAROHCNA
SAMANTHA V. REDICK
R E G
ISTEREDP
E
0
R
E
1
O
-
/
1
F
1
E
1
5
S
7
/
S
2
9
I
6
O
8
N
7
AL
ENGI
NE E R
ELECTRICAL SPECIFICATIONS
SECTION 26 05 00 - COMMON WORK RESULTS FOR ELECTRICAL SECTION 26 27 26 - WIRING DEVICES
1. PROVIDE MATERIALS AND EQUIPMENT THAT ARE PRODUCTS OF MANUFACTURERS
1. PROVIDE RECEPTACLES, CONNECTORS, SWITCHES, AND FINISH PLATES OF TYPES AND
REGULARLY ENGAGED IN THE PRODUCTION OF SUCH PRODUCTS. ALL MATERIALS QUANTITIES SUITABLE FOR THE PROJECT AND INTENDED USE. WIRING DEVICES SHALL
SHALL BE LISTED AND LABELED FOR THE APPLICATION WITH A NATIONALLY
MEET NEMA WD 1 AND NEMA WD 6. WIRING TERMINALS SHALL BE OF THE SCREW TYPE
RECOGNIZED TESTING LABORATORY IN ACCORDANCE WITH NFPA 70.
OR OF THE SOLDERLESS PRESSURE TYPE HAVING SUITABLE CONDUCTOR-RELEASE
ARRANGEMENT. WIRING DEVICES SHALL BE IMPACT RESISTANT NYLON WITH WHITE
2. MATERIALS AND EQUIPMENT SHALL BE INSTALLED IN ACCORDANCE WITH ALL
COLOR UNLESS NOTED OTHERWISE.
REQUIREMENTS OF THE LATEST EDITION OF THE NATIONAL ELECTRIC CODE, STATE,
MUNICIPAL, AND FEDERAL LAWS, AND AMENDMENTS GOVERNING THE PROJECT.
2. DEVICE PLATES ON UNFINISHED WALLS MAY BE OF ZINC-COATED SHEET STEEL, OR
INSTALLATION OF EQUIPMENT SHALL BE ACCORDANCE WITH THE WRITTEN
CAST METAL HAVING ROUNDED OR BEVELED EDGES. DEVICE AND DEVICE PLATES ON
INSTRUCTIONS RECOMMENDATIONS OF THE MANUFACTURER.
FINISHED WALLS SHALL BE WHITE AND MATCH DEVICE COLOR. SCREWS SHALL BE OF
METAL WITH COUNTERSUNK HEADS, IN A COLOR TO MATCH THE FINISH OF THE PLATE.
3. THE CONTRACTOR SHALL BECOME FAMILIAR WITH ALL DETAILS OF WORK AND VERIFY
ALL DIMENSIONS IN THE FIELD SO THAT ALL OUTLETS AND EQUIPMENT ARE PROPERLY
3. SINGLE AND DUPLEX RECEPTACLES SHALL BE RATED 20 AMPERES, 125 VOLTS, 2-POLE,
LOCATED AND READILY ACCESSIBLE.
3-WIRE, GROUNDING TYPE WITH POLARIZED PARALLEL SLOTS, BACK AND SIDE WIRED.
4. LIGHTING FIXTURES, OUTLETS, AND OTHER EQUIPMENT AND MATERIALS SHALL BE
4. TOGGLE SWITCHES SHALL BE RATED 120-277 VOLT AC GROUNDING TYPE, TOTALLY
COORDINATED WITH STRUCTURAL FEATURES AND ALL OTHER TRADES PRIOR TO
ENCLOSED, GENERAL USE.
INSTALLATION. IF ANY CONFLICTS OCCUR NECESSITATING DEPARTURES FROM THE
SECTION 26 51 00- INTERIOR LIGHTING
DRAWINGS, DETAILS OF, AND REASONS FOR DEPARTURES SHALL BE SUBMITTED AND
ACCEPTED PRIOR TO IMPLEMENTING ANY CHANGE. 1. PROVIDE AND INSTALL ALL LIGHTING EQUIPMENT AS SHOWN ON THE DRAWINGS AND
SPECIFIED IN THE LIGHTING FIXTURE SCHEDULE. PROVIDE WITH ALL OPTIONS AND
5. THE LISTED PUBLICATIONS BELOW ESTABLISH MINIMUM REQUIREMENTS FOR
ACCESSORIES AS REQUIRED FOR A COMPLETE INSTALLATION IN COMPLIANCE WITH
MATERIALS, SYSTEMS AND EXECUTION THAT MAY BE SPECIFIED IN THIS SECTION AND
THE MANUFACTURER'S INSTALLATION INSTRUCTIONS.
UTILIZED FOR THIS PROJECT.
2. PAINT ALL EXPOSED RACEWAYS AND BOXES TO MATCH ADJACENT SURFACES.
A.NATIONAL ELECTRICAL CONTRACTORS ASSOCIATION (NECA): NECA 1 - STANDARD
PRACTICES FOR GOOD WORKMANSHIP IN ELECTRICAL CONSTRUCTION SECTION 28 31 11 - DIGITAL FIRE ALARM SYSTEM
B. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA): NFPA 70 NATIONAL ELECTRICAL 1. GENERAL: PROVIDE A COMPLETE, NON-CODED ADDRESSABLE,
CODE, NFPA 70E STANDARD FOR ELECTRICAL SAFETY IN THE WORKPLACE. MICROPROCESSOR-BASED FIRE ALARM SYSTEM WITH INITIATING DEVICES,
NOTIFICATION APPLIANCES, AND MONITORING AND CONTROL DEVICES AS SPECIFIED
SECTION 26 05 19 - POWER CONDUCTORS AND CABLES
HEREIN. FURNISH AND INSTALL A COMPLETE FIRE ALARM SYSTEM AS DESCRIBED
1. PROVIDE WIRING, CABLES AND ASSOCIATED SPLICES, CONNECTORS, AND HEREIN AND AS SHOWN ON THE PLANS. INCLUDE SUFFICIENT CONTROL UNIT(S),
TERMINATIONS FOR WIRING SYSTEMS RATED 600 VOLTS AND LESS. CONDUCTOR ANNUNCIATOR(S), MANUAL STATIONS, AUTOMATIC FIRE DETECTORS, SMOKE
AMPACITY SHALL BE BASED ON TABLE 310-16 OF THE NEC UTILIZING THE 60-DEGREE C. DETECTORS, AUDIBLE AND VISIBLE NOTIFICATION APPLIANCES, WIRING,
RATING COLUMN FOR CIRCUITS TERMINATING ON DEVICES RATED BELOW 100 AMPS TERMINATIONS, ELECTRICAL BOXES, ETHERNET DROPS, AND ALL OTHER NECESSARY
AND THE 75-DEGREE C RATING COLUMN FOR CIRCUITS TERMINATING ON DEVICES AND MATERIAL FOR A COMPLETE OPERATING SYSTEM. PLEASE NOTE: THE DEVICE LAYOUT
IN ENCLOSURES RATED 100 AMPS AND GREATER. AS INDICATED ON THE DRAWINGS IS DIAGRAMMATIC IN NATURE AND IS NOT INTENDED
TO INDICATE A FULL INSTALLATION. RATHER IT IS INTENDED TO INDICATE SCOPE AND
2. ALL CONDUCTORS SHALL BE COPPER UNLESS NOTED OTHERWISE. ALL CONDUCTORS
EXTEND OF DESIRED LAYOUTS. IT SHALL BE THE CONTRACTORS RESPONSIBILITY TO
INSTALLED IN UNHEATED SPACES WITHIN THE BUILDING, UNDERGROUND, OR LOCATED
PROVIDE A FULLY CODE COMPLIANT SYSTEM.
OUTSIDE OF THE BUILDING SHALL HAVE TYPE XHHW 90 DEGREE C INSULATION. ALL
CONDUCTORS INSTALLED WITHIN HEATED SPACES MAY HAVE XHHW OR THHN 90 2. UFAS - ALL UNITS MUST COMPLY WITH THE UNIFORM FEDERAL ACCESSIBILITY
DEGREE C INSULATION. STANDARDS (UFAS). UNITS AND SHALL BE PROVIDED WITH FIRE ALARM DEVICES AND
CONNECTIONS AS REQUIRED TO BE CODE COMPLIANT WITH SAID ACT,
3. CONDUCTORS NO. 8 AWG AND LARGER DIAMETER SHALL BE STRANDED. CONDUCTORS
NO. 12 AWG AND SMALLER SHALL BE SOLID, EXCEPT THAT CONDUCTORS FOR REMOTE 3. PROVIDE SUBMITTAL AS FOLLOWS: PRODUCT DATA SHEETS FOR SYSTEM
CONTROL, ALARM, AND SIGNAL CIRCUITS, CLASSES 1, 2, AND 3 SHALL BE STRANDED. COMPONENTS HIGHLIGHTED TO INDICATE THE SPECIFIC PRODUCTS, FEATURES, OR
FUNCTIONS REQUIRED TO MEET THIS SPECIFICATION. WIRING DIAGRAMS FROM
4. BRANCH CIRCUITS: CONDUCTORS SHALL BE NOT SMALLER THAN NO. 12 AWG.
MANUFACTURER. SHOP DRAWINGS SHOWING SYSTEM DETAILS INCLUDING LOCATION
CONDUCTORS FOR BRANCH CIRCUITS OF 120 VOLTS MORE THAN 100 FEET LONG AND
OF FACU, ALL DEVICES, CIRCUITING AND DETAILS OF GRAPHIC ANNUNCIATOR. SYSTEM
OF 277 VOLTS MORE THAN 200 FEET LONG FROM PANEL TO FARTHEST DEVICE OR
POWER AND BATTERY CALCULATIONS AND VOLTAGE DROP CALCULATIONS TO ASSURE
LOAD, SHALL BE NO SMALLER THAN NO. 10 AWG. CONDUCTORS FOR BRANCH CIRCUITS
THAT THE SYSTEM WILL OPERATE IN ACCORDANCE WITH THE PRESCRIBED BACKUP
OF 120 VOLTS MORE THAN 150 FEET LONG AND OF 277 VOLTS MORE THAN 300 FEET
TIME PERIODS AND UNDER ALL VOLTAGE CONDITIONS PER UL AND NFPA STANDARDS
LONG FROM PANEL TO FARTHEST DEVICE OR LOAD, SHALL BE NO SMALLER THAN NO. 8
AWG. 4. SUBMISSION TO AUTHORITY HAVING JURISDICTION: IN ADDITION TO ROUTINE
SUBMISSION OF THE ABOVE MATERIAL, MAKE AN IDENTICAL SUBMISSION TO THE
5. TYPE NM CABLE IS ACCEPTABLE FOR USE IN THE RESIDENTIAL AREAS AS ALLOWED BY
AUTHORITY HAVING JURISDICTION. INCLUDE COPIES OF SHOP DRAWINGS AS REQUIRED
THE NATIONAL ELECTRICAL CODE.
TO DEPICT COMPONENT LOCATIONS TO FACILITATE REVIEW. UPON RECEIPT OF
6. INSTALL CONDUCTORS IN COMPLIANCE WITH NEC REQUIREMENTS FOR TEMPERATURE COMMENTS FROM THE AUTHORITY, MAKE RESUBMISSIONS, IF REQUIRED, TO MAKE
AND CONDUIT FILL DERATING AND BOX FILL LIMITATIONS. CLARIFICATIONS OR REVISIONS TO OBTAIN APPROVAL.
7. COLOR CODE CONDUCTORS AS FOLLOWS: 5. THE FIRE ALARM SYSTEM SHALL CONSIST OF ALL NECESSARY HARDWARE EQUIPMENT
AND SOFTWARE PROGRAMMING TO PERFORM THE FOLLOWING FUNCTIONS:
A.120/208 VOLT, 1 PHASE, 3 WIRE: BLACK, RED, WHITE
6. FIRE ALARM SYSTEM DETECTION AND NOTIFICATION OPERATIONS. CONTROL AND
B.120/208 VOLT, 3 PHASE, 4 WIRE: BLACK, RED, BLUE, WHITE MONITORING OF ELEVATORS, DOOR HOLD-OPEN DEVICES, FIRE SUPPRESSION
SYSTEMS, AND OTHER EQUIPMENT AS INDICATED IN THE DRAWINGS AND
8. NEUTRAL (GROUNDED) CONDUCTOR: PROVIDE AN UNSHARED DEDICATED NEUTRAL
SPECIFICATIONS. SYSTEM OPERATION DESCRIPTION INCLUDING METHOD OF
FOR EACH CIRCUIT UNLESS SPECIFICALLY NOTED OTHERWISE. IDENTIFY GROUNDED
OPERATION AND SUPERVISION OF EACH TYPE OF CIRCUIT AND SEQUENCE OF
CONDUCTORS PER NEC FOR ALL CIRCUITS
OPERATIONS FOR ALL MANUALLY AND AUTOMATICALLY INITIATED SYSTEM INPUTS AND
9. GROUNDING CONDUCTORS: PROVIDE A GREEN EQUIPMENT GROUNDING CONDUCTOR OUTPUTS. A LIST OF ALL INPUT AND OUTPUT POINTS IN THE SYSTEM SHALL BE
IN EACH NEW RACEWAY, SIZED IN ACCORDANCE WITH NFPA 70, REGARDLESS OF THE PROVIDED WITH A LABEL INDICATING LOCATION OR USE OF IDC, SLC, NAC, RELAY,
TYPE OF CONDUIT. SENSOR, AND AUXILIARY CONTROL CIRCUITS. OPERATING INSTRUCTIONS FOR FACU.
SECTION 26 05 33 - RACEWAYS AND BOXES FOR ELECTRICAL SYSTEMS 7. OPERATION AND MAINTENANCE DATA FOR INCLUSION IN OPERATING AND
MAINTENANCE MANUAL. INCLUDE DATA FOR EACH TYPE PRODUCT, INCLUDING ALL
1. PROVIDE RACEWAYS AND BOXES LISTED AND SUITABLE FOR THE PROPOSED
FEATURES AND OPERATING SEQUENCES, BOTH AUTOMATIC AND MANUAL. PROVIDE
APPLICATION. PROVIDE AN EFFICIENTLY LAID OUT SYSTEM THAT ALLOWS FOR FUTURE
THE NAMES, ADDRESSES, AND TELEPHONE NUMBERS OF SERVICE ORGANIZATIONS.
GROWTH. COORDINATE RACEWAYS WITH THE WORK OF OTHER TRADES, AND
COORDINATE LAYOUT AND CONSTRUCTION WITH OTHER CONSTRUCTION ELEMENTS
8. THE SYSTEM AS INDICATED IS BASED ON A EST IO SERIES. APPROVED EQUALS WILL BE
TO ENSURE MAXIMUM HEADROOM, WORKING CLEARANCE, AND ACCESS.
CONSIDERED.
2. UTILIZE RACEWAY SYSTEMS LISTED AND SUITABLE FOR THE ENVIRONMENT INSTALLED
9. INSTALL SYSTEM COMPONENTS AND ALL ASSOCIATED DEVICES IN ACCORDANCE WITH
AS DEFINED BELOW:
APPLICABLE NFPA STANDARDS AND MANUFACTURER'S RECOMMENDATIONS.
INSTALLATION PERSONNEL SHALL BE SUPERVISED BY PERSONS WHO ARE QUALIFIED
A.OUTDOORS (EXPOSED): WEATHERPROOF RIGID STEEL CONDUIT OR EMT SYSTEM.
AND EXPERIENCED IN THE INSTALLATION, INSPECTION, AND TESTING OF FIRE ALARM
B.INDOORS (NOT SUBJECT TO PHYSICAL DAMAGE): EMT, MC OR NM CABLE. SYSTEMS. INSTALLATION SHALL BE BY PERSONNEL LICENSED OR CERTIFIED BY STATE
OF ALASKA.
C.CONNECTION TO VIBRATING EQUIPMENT: FLEXIBLE METAL CONDUIT, LIQUID-TIGHT
IN DAMP AND WET LOCATIONS. 10.SEQUENCING: CONTRACTOR SHALL COORDINATE WITH THE OWNER FOR PROPER
SEQUENCING FOR ALARM CONDITIONS FOR ALL ELEMENTS OF THE BUILDING AND
SPECIFICALLY HOW DWELLING UNIT ALARMS ARE SEQUENCED TO COMMON AREA
ALARMS.
11.TRAINING: PROVIDE THE SERVICES OF A FACTORY-AUTHORIZED SERVICE
REPRESENTATIVE TO DEMONSTRATE THE SYSTEM AND TRAIN OWNER'S MAINTENANCE SVR
PERSONNEL. PROVIDE A MINIMUM OF 4 HOURS' TRAINING. SCHEDULE TRAINING WITH TCA
THE OWNER AT LEAST SEVEN DAYS IN ADVANCE.
SPECIFICATIONS
E0.02
PERMIT DOCUMENTS
