Advertisement for Bid
Lee County, AL
Lee County is taking sealed bids for labor, equipment, materials, and any incidentals required to complete
the work required for PROJECT NO. LCP 41-AR-27 – PLACEMENT OF A REJUVENATING FOG SEAL
ON VARIOUS ROADS IN LEE COUNTY, AL (Approx. 32 lane miles). This bid is intended to comply with
the Rebuild Alabama Act, Act No. 2019-2, as amended, and the Alabama Public Works Law, Alabama
Code Title 39, as amended. Bidders shall be required to comply with the provisions of the Rebuild
Alabama Act, Act No. 2019-2, as amended, and the Alabama Public Works Law, Alabama Code Title 39,
as amended, regardless if the requirement is explicitly detailed in the bid proposal or not.
Ala. Code § 39-3-5 applies to this project. In accordance with Ala. Code § 39-3-5(a), “…. preference shall
be given to resident contractors, and a nonresident bidder domiciled in a state having laws granting
preference to local contractors shall be awarded Alabama public contracts only on the same basis as the
nonresident bidder's state awards contracts to Alabama contractors bidding under similar circumstances;
and resident contractors in Alabama, as defined in Section 392-12, be they corporate, individuals, or
partnerships, are to be granted preference over nonresidents in awarding of contracts in the same manner
and to the same extent as provided by the laws of the state of domicile of the nonresident.”
As a condition for award, the business entity and its subcontractors shall not knowingly employ or hire an
unauthorized alien within the State of Alabama. The awarded business entity must provide documentation
of enrollment in the E-Verify program. The business must participate in the E-Verify program for the length
of the contract.
The Entire Project Shall Be Completed in One Hundred and Twenty (120) Calendar Days.
Cashier’s check or bid bond for 5% of bid (maximum - $10,000.00) made payable to the Lee County
Commission must accompany each bid as evidence of good faith. Bids will not be considered unless the
bid bond form provided in the proposal is used.
Sealed bids will be received by the Lee County Commission at 215 S. 9th Street, Opelika, AL 36801 or mailed
to P.O. Box 2412, Opelika, AL 36803-2412 until 10:00 AM Central Time on November 18, 2026, and then publicly
opened as soon thereafter as practicable. Award will be made at the next regularly scheduled meeting of the Lee
County Commission.
Specifications are on file and may be acquired at the Lee County Engineering Department,
2555 Society Hill Road, Opelika, Alabama 36804.
Phone Number: (334) 737-7011
Lee County Engineering Department Hours of Operation are 6:00 A.M. to 4:30 P.M. (Central Time)
Monday through Thursday.
County reserves the right to accept or reject all Bids or any portion thereof.
PROPOSAL NO.
, 2026
FOR THE CONSTRUCTION OF LEE COUNTY
PROJECT NO. LCP 41-AR-27
LEE COUNTY, ALABAMA
Proposal of
Contractor Name:
Of (City, State):
Alabama General Contractors License Number:
For constructing the
PLACEMENT OF A REJUVENATING FOG SEAL ON VARIOUS ROADS IN LEE COUNTY, AL
(APPROXIMATE LENGTH = 32 LANE MILES)
The plans are composed of the drawings identified as follows:
County Project No. LCP 41-AR-27
The specifications are hereto attached.
In order to be considered, proposals must be received at the location and time below:
Lee County Commission
215 S. 9th Road
Opelika, Alabama 36801
Phone: (334) 737-7011
BEFORE: 10:00 AM on Wednesday, November 18, 2026
Bids will be opened as soon thereafter as practicable. Award will be made at the next regularly scheduled meeting
of the Lee County Commission.
Bidder’s Initials:
INSTRUCTIONS TO BIDDERS
1. PREPARATIONS OF BIDS:
Forms furnished, or copies thereof, shall be used, and strict compliance with the requirements of the invitation,
these instructions, and the instructions printed on the forms is necessary. Special care should be exercised
in the preparation of bids. Bidders must make their own estimates of the facilities and difficulties attending
the performance of the proposed contract, including local conditions, uncertainty of weather, and all other
contingencies. All designations and prices shall be fully and clearly set forth. The proper space in the bid and
guaranty/bid bond forms shall be suitably filled in. As a condition for award, the business entity and its
subcontractors shall not knowingly employ or hire an unauthorized alien within the State of Alabama. The
awarded business entity must provide documentation of enrollment in the E-Verify program. The business
must participate in the E-Verify program for the length of the contract.
2. LABOR AND MATERIALS NOT TO BE FURNISHED BY LEE COUNTY, ALABAMA:
The County Commission of Lee County, Alabama, will not furnish any labor, material, or supplies unless
specifically provided in the Contract.
3. SIGNATURE TO BIDS:
Each bid must give the full business address of the Bidder and must be signed by the Bidder with their usual
signature. Bids by partnerships must furnish the full names of all partners and must be signed with the
partnership name by one of the members of the partnership, or by an authorized representative, followed by
the signature and designation of the person signing. Bids by corporations must be signed with the legal
name of the corporation followed by the name of the State of Incorporation and by the signature and
designation of the president, secretary, or other person authorized to bind it in the matter. The name of each
person shall also be typed or printed below the signature. A bid by a person who affixes to this signature the
word "president," "secretary," "agent," or other designation without disclosing his principal, may be held to
be the bid of the individual signing. When requested by the County Commission of Lee County, Alabama,
satisfactory evidence of the authority of the officer signing in behalf of the corporation shall be furnished.
4. BIDS FOR ALL OR PART:
Each project will be bid separately unless otherwise expressly requested in the Proposal. Combination bids,
that are bids on separate projects lumped together as a single bid or on all or none bid or on all or none
basis, will not be accepted unless the Proposal expressly requests or permits same.
5. ALTERNATE BIDS:
Alternate bids will not be considered unless called for.
Bidder’s Initials:
6.
SPECIFICATIONS AND SCHEDULES:
Asphalt Rejuvenating Fog Seal:
(a) General Scope: This work shall consist of furnishing all labor, material and equipment
necessary to perform the operations for the application of an Emulsified Maltene-Based
Asphalt Rejuvenating Fog Seal to bituminous asphaltic surface courses. The rejuvenation of
surface courses shall be by spray application of a cationic Maltene-Based Rejuvenating Fog
Seal composed of petroleum oils and resins emulsified with water. The base used for the
emulsion shall be a naphthenic base stock. The asphalt binder rejuvenation shall be affected
through maltene replacement technology. All work shall be in accordance with the
specifications, any applicable drawings, and subject to the terms and conditions of this
contract.
(b) Pre-Construction: The contractor shall present laboratory reports, calibration reports,
and proof of work experience as required by these specifications with their bid submittal.
(c) Material Specifications: The emulsion shall be a naphthenic petroleum maltene-based rejuvenating
fog seal composed of petroleum maltene components uniformly emulsified with water. Aromatics
(maltenes) shall be derived from a naphthenic petroleum base stock (naphthene-aromatics). Paraffin-
based petroleum will not be accepted.
(d) Material Performance: The asphalt rejuvenating fog seal shall have the capability to
penetrate the asphalt pavement surface and perform as follows. The asphalt rejuvenating fog
seal shall be absorbed and incorporated into the asphalt binder. Verification that said
incorporation of the asphalt rejuvenating fog seal into the asphalt binder has taken place shall
be by analysis of the chemical properties of said asphalt binder, at no additional cost to the
County, and viscosity shall be reduced by petroleum maltene fraction replacement method to
the following extent:
• For pavement receiving a first or original application within the first 12 months of paving,
viscosity shall be reduced by an average of twenty-five (25%). For pavements receiving a
first or original application after pavement has been installed more than 12 months,
viscosity shall be reduced by an average of thirty (30%). These are to be determined by
the dynamic shear rheometer (DSR) method for asphalt testing in accord with AASHTO
T315-05, extraction ASTM 2172, Recovery ASTM D5404.
• For retreated pavements after an initial treatment with the asphalt rejuvenator the
viscosity shall be reduced by petroleum maltene replacement method a minimum of twenty
percent (20%) as determined by dynamic shear rheometer (DSR) method for testing in
accordance with AASHTO T315-05. In addition, the phase angle shall be increased. This
analysis shall apply to extracted asphalt binder taken from cores extracted thirty (30) to
sixty (60) days following application, in the upper three eights inch (3/8”) of pavement. In
addition, the treated areas shall be sealed to the intrusion of air and water.
(e) The bidder must submit the following with their bid:
Bidder’s Initials:
• Asphalt Rejuvenator product name and descriptive literature. Literature shall be descriptive and
detailed information and shall show it meets the material specifications.
•A current Material Safety Data Sheet (SDS) for the material.
• Previous use documentation and test data conclusively demonstrating that the rejuvenating fog
seal has been used successfully by government agencies.
• Testing data from a minimum of three (3) projects showing that the asphalt rejuvenating fog seal
has been proven to perform, as required, through field testing by an independent testing laboratory as
to the required change in the asphalt binder viscosity and percent asphaltene content.
(f) Applicator Experience: The asphalt rejuvenating fog seal shall be applied by an experienced
applicator. The bidder shall have a minimum of 3 years’ experience in applying the product proposed for
use on municipal, county, or state roads. The Contractor must submit with his bid a list of three (3)
projects on which he applied said rejuvenator. Indicate the project dates, number of square yards treated
in each, and the name and phone number of the manager in charge of each project.
(g) Project Superintendent: A project superintendent knowledgeable and experienced in application of
the asphalt rejuvenating fog seal must be present and in control of each day’s work.
(h) Application Temperature and Weather Limitations: The temperature of the asphalt rejuvenation
emulsion, at the time of application, shall be as recommended by the manufacturer. The asphalt
rejuvenating fog seal shall be applied only when the existing surface to be treated is thoroughly dry.
Application shall not take place within 24 hours of rainfall having occurred or is reasonably expected to
occur. The asphalt rejuvenating fog seal shall not be applied when the ambient temperature is below 40
degrees Fahrenheit or when temperatures are forecasted to fall below 35 degrees Fahrenheit within
twenty-four (24) hours of application. It shall be the discretion of the County Engineer to determine when
weather conditions are not appropriate for the application to occur. Contractor shall halt the application
process when so ordered by the County Engineer.
(i) Handling of Asphalt Rejuvenating Fog Seal: Contents in tank cars or storage tanks shall be
circulated at least forty-five minutes before withdrawing any material for application. When loading the
distributor, the asphalt rejuvenating fog seal concentrate shall be loaded first and then the required
amount of water shall be added. The water shall be added into the distributor with enough force to cause
agitation and thorough mixing of the two (2) materials. To prevent foaming, the discharge end of the
water hose or pipe shall be kept below the surface of the material in the distributor which shall be used as
a spreader. The distributor truck will be cleaned of all of its asphalt materials, and washed out to the
extent that no discoloration of the emulsion may be perceptible. Cleanliness of the spreading equipment
shall be subject to inspection and the Contractor shall halt the application process when so ordered by
the County Engineer
(j) Application Equipment: The distributor for applying the asphalt rejuvenating fog seal shall be self-
propelled and have pneumatic tires. The distributor shall be designed and equipped to distribute the
asphalt rejuvenating fog seal uniformly on variable widths of surface at readily determined and controlled
rates from 0.04 to 0.5 gallons per square yard of surface, and with an allowable variation from any
Bidder’s Initials:
This is the opportunity summary page. It provides an overview of this opportunity and a preview of the attached documentation.