SOURCES SOUGHT STEEL GRIT IDIQ

Active

Contract Opportunity

SOURCES SOUGHT- SOLE SOURCE INTENT

THIS NOTICE OF INTENT IS NOT A REQUEST FOR QUOTES. A DETERMINATION NOT TO COMPETE THE PROPOSED PROCUREMENT BASED UPON RESPONSES TO THIS NOTICE IS SOLELY WITHIN THE DISCRETION OF THE GOVERNMENT.

DLA Weapons Support, hereby provides notice of its intent to award a sole-source, IDIQ contract consisting of a Base Year and 4 option years to ERVIN INDUSTRIES, Cage code 55807. The contract is expected to be awarded under FAR 6.302-1. A Justification and Approval for Other than Full and Open Competition has been prepared.

ITEM INFORMATION

STEEL GRIT, NAICS code: 327910

NSN: LLN050404

ABRASIVE, CAST STEEL GRIT

A. IAW SAE J1993, 10/2013

B. G50 PER SAE J444, 9/2012

C.NEW MFR ONLY PER SSPC AB3, ROCKWELL

HARDNESS 54-61 HRC PER SAE J1993 (LG HARDNESS)

D. DURABILITY PER SSPC AB3

E. STEEL DRUMS INSIDE AND OUTSIDE ARE REQUIRED

TO BE POLY-LINED AND SEALED, PALLETS ARE REQUIRED

TO BE POLY COVERED

**** MERCURY FREE APPLIES *****

a. ASTM B 215 Method B will not be used to draw samples for testing. Keystone samplers and sample splitters will not be used. A representative sample will be drawn from drums per the following sample schedule.

Lot Size Sample Size

2 to 15 drums 2

16 to 25 drums 3

26 to 90 drums 5

91 to 150 drums 8

151 to 280 drums 13

281 to 500 drums 20

501 to 1,200 drums 32

1201 to 3,200 drums 50

3201 to 10,000 drums 80

b. For hardness testing, ten particles will be tested from each sample per SAE J1993 paragraph 10.4 and ASTM E 384. Three hardness readings will be taken on each particle. Ninety percent of the hardness readings for each sample shall be within the specified range.

C. The samples will be tested for conformance to other chemical and physical properties as defined in SAE J1993.

d. If one sample fails the entire order shall fail and all batches delivered as part of that order shall be rejected. Sampling and testing of each batch delivered shall not be required.

THIS NOTICE OF INTENT IS NOT A REQUEST FOR COMPETITIVE QUOTES. However, interested parties may identify their interest and capability to respond to this requirement no later than

January 9, 2026 at 08:00 AM Pacific Time.

A determination not to compete this requirement based upon responses to this notice, is solely within the discretion of the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement.

DLA Weapons Support will NOT be responsible for any costs incurred by interest parties in responding to this notice of intent. Only written responses will be considered. All responses from responsible sources will be fully considered. As a result of analyzing responses to this notice of intent, the Government shall determine if a solicitation will be issued. Any prospective contractor must be registered in the System for Award Management (SAM) in order to be eligible for award.

Interest parties are encouraged to furnish information by email only with RESPONSE TO INTENT TO SOLE SOURCE FOR STEEL GRIT IDIQ in the subject line. All documents submitted will not be returned. All interested parties shall submit, via email, clear and convincing documentation demonstrating their capabilities to satisfy the requirements listed above to the Contract Specialist at TRICIA.WINTERSTEEN@DLA.MIL .

If your organization has clear and convincing documentation demonstrating your capability to support this requirement, please provide the following information:

1) Organization name

Address

Email address

Web site address

Telephone number

Business size

Type of ownership for the organization

Vendor Cage Code;

2) Tailored capability statements addressing the particulars of this effort, with appropriate documentation supporting claims of organizational and staff capability. If significant subcontracting or teaming is anticipated in order to deliver technical capability. The capability documentation should include general information and technical background describing in detail the prospective contractor's capabilities and experience that will demonstrate the ability to support these requirements. Organizations should address all of these areas identified.

Attachments/Links