HOSES

Active

Contract Opportunity

SOURCES SOUGHT SYNOPSIS

HOSES

The Defense Logistics Agency Maritime Puget Sound is issuing this sources sought and request for information as a means of conducting market research to identify parties having an interest in and the resources to support a material requirement in Bremerton, WA.

1. HOSE 3/4" X 25' XTRA FLEX 250PSI CORRUGATED PETROLEUM HOSE COUPLED MALE X FEMALE HD BRASS CAMLOCKS SS COLLARS

A-2225-075-025-CLS2&E-BR

MODEL

1) Unisource Manufacturing, 1” Xtra-flex 250psi Corrugated tank truck petroleum hose. 2225-075-025

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Carboxylated Nitrile Cover: Coupled and Fully Assembled.

Application for Intended Use: Will be installed in a marine environment for use in Temporary Services for Shipboard Seawater / Fresh Water Suction/Discharge Services. When not in use, the hose will be coiled and stacked for storage in an area with fluorescent lighting.

1. Size: 3/4” I.D. by 25’ long.

2. Nominal OD: 1.20”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 10 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

1. Tube: Extruded Nitrile synthetic rubber. Must meet Association for Rubber Product Manufacturers (ARPM) Class B standard for medium/high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

2. Reinforcement: Multiple braids of textile fabric with a high-tensile wire helix.

3. Cover: Carboxylated Nitrile Rubber with high abrasion resistance. The cover shall be formulated to provide resistance to UV and weathering adequate to prevent failure due to these causes for a minimum of 10 years when installed and stored described in this specification. ARPM Class A high oil resistance. High ozone resistance.

4. Cover Color: Black Outer Cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End: Brass, 1” Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and

Passive Locking Device. PT Coupling Company, Part # 3/4CSLII, Item # 1290307.

b. 2nd Hose End: Brass, 1” Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 3/4E, Item # 1200507.

c. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., PROGRIP™ C50SS Stainless Steel Crimp Ferrules. Ferrules to be sized to match the hose and end fittings. No “or equal” bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from virgin brass, meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS & IMF Code 270TS.

8. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked with ½” minimum height lettering in a contrasting color to the Red band strip and Black Outer Cover of the hose.

The lettering shall state as a minimum:

1. Standard Hose Brand/Line/Model number, Working Pressure, Date of Manufacture


2. PSNS & IMF S/99

9. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product

description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors, if requested, must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

11. All ”Or-Equal” offers must be approved by PSNS & IMF Temporary Services Engineering, Code 270TS prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each certified hose assembly is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested certification for each hose assembly shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: PSNS&IMFINST 10330.11F, PSNS&IMF 11300.10K, Industrial Process Instruction 0505-904C CH-2, Codes of Federal Regulations Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A-59326.

2. HOSE 3/4" X 50' XTRA FLEX 250PSI CORRUGATED PETROLEUM HOSE COUPLED MALE X FEMALE HD BRASS CAMLOCKS SS COLLARS

A-2225-075-050-CLS2&E-BR

MODEL:

1) Unisource Manufacturing, 1” Xtra-flex 250psi Corrugated tank truck petroleum hose. 2225-075-025

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Carboxylated Nitrile Cover: Coupled and Fully Assembled.

Application for Intended Use: Will be installed in a marine environment for use in Temporary Services for Shipboard Seawater / Fresh Water Suction/Discharge Services. When not in use, the hose will be coiled and stacked for storage in an area with fluorescent lighting.

1. Size: 3/4” I.D. by 50’ long.

2. Nominal OD: 1.20”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 10 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

1. Tube: Extruded Nitrile synthetic rubber. Must meet Association for Rubber Product Manufacturers (ARPM) Class B standard for medium/high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

2. Reinforcement: Multiple braids of textile fabric with a high-tensile wire helix.

3. Cover: Carboxylated Nitrile Rubber with high abrasion resistance. The cover shall be formulated to provide resistance to UV and weathering adequate to prevent failure due to these causes for a minimum of 10 years when installed and stored described in this specification. ARPM Class A high oil resistance. High ozone resistance.

4. Cover Color: Black Outer Cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End: Brass, 1” Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and

Passive Locking Device. PT Coupling Company, Part # 3/4CS, Item # 1290307.

b. 2nd Hose End: Brass, 1” Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 3/4E, Item # 1200507.

c. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., PROGRIP™ C50SS Stainless Steel Crimp Ferrules. Ferrules to be sized to match the hose and end fittings. No “or equal” bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from virgin brass, meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS & IMF Code 270TS.

8. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked with ½” minimum height lettering in a contrasting color to the Red band strip and Black Outer Cover of the hose.

The lettering shall state as a minimum:

1. Standard Hose Brand/Line/Model number, Working Pressure, Date of Manufacture


2. PSNS & IMF S/99

9. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors, if requested, must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

11. All ”Or-Equal” offers must be approved by PSNS & IMF Temporary Services Engineering, Code 270TS prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each certified hose assembly is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested certification for each hose assembly shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: PSNS&IMFINST 10330.11F, PSNS&IMF 11300.10K, Industrial Process Instruction 0505-904C CH-2, Codes of Federal Regulations Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A-59326.

3. HOSE 1-1/4" X 25' LPA 250PSI SMOOTH COVER HOSE COUPLED MALE X FEMALE HD BRASS CAMLOCKS SS COLLARS

A-2194-125250-025-CLS2&E-BR

Fully Coupled, Non Metallic Hose Assembly

1-1/4” I.D. by 25’ Long.

Model:

1. 1-1/4” Goodyear, Air & Multipurpose Hose, Wingfoot 250.


2. 1-1/4” Gates, Air and Multi-Purpose Hose, Premo Flex 3205R/3205B.


3. 1-1/4” Unisource Manufacturing, Air and Multi-Purpose Hose, 2194-125250-050.

Or Equal Criteria:

Hose, Nonmetallic, Nitrile Tube and Nitrile or Synthetic Rubber Outer Cover: Coupled and Fully Assembled.

1. Application: Low-pressure Air (LPA) services.


2. Working Pressure: 250 PSI Maximum.


3. Burst Pressure: 1,000 PSI Minimum.


4. Bend Radius: Minimum rated bend radius, 9 inches.


5. Rated Continuous Temperature: –20° F to +190° F.

Hose Construction:

1. Tube: Nitrile synthetic rubber. Must meet Rubber Manufactures Association (RMA) Class A standard for high oil resistance.


2. Cover: Nitrile or Synthetic rubber. To meet RMA Class B standards for medium-high oil resistance


3. Cover Color: Red (Black is acceptable). An all yellow outer cover is not acceptable.


4. Reinforcement: Spiral synthetic yarn.


5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories Distribution (NAHAD) certification standards.


6. Each hose assembly shall have the following components installed at each end:

•1st Hose End: 1-1/4" Female Cam & Groove x Hose Shank Coupler, Brass with Stainless Steel Cam Arms, Pins, Pull Rings and Passive Locking Device, PT Coupling Co., Part # 12CSLII, Item # 1290312L2.

• 2nd Hose End: 1-1/4" Male Cam & Groove x Hose Shank Adapter, Brass, PT Coupling Co., Part # 12E, Item # 1200512.

• End Fitting Interlocking Ferrules: End Fittings shall be coupled to the hose with PT Coupling Co., "ProGrip" C50SS Stainless Steel Crimp Ferrules. Ferrules to be size matched to the hose and end fittings. No "or equal" bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from US virgin brass with a machined finish IAW Commercial Item Description (CID) A-A-59326 and shall have a working pressure or 250 PSI or greater.

8. Branding / Markings: In addition to the manufacturer’s standard markings the hose is to be continuously Mylar or Stripe Branded / marked the following in 1/2” (minimum) lettering, which must be in a contrasting color or background to the outer cover of the hose. The lettering shall state as a minimum: A. Standard Hose Brand Line/Model Number and Date of Manufacture.

B. “LP AIR” or “LOW PRESSURE AIR”

C. “250 PSI MAX WP”

D. “PSNS S/99”

9. All vendor price quotes or offers must include an original manufacturer’s cut sheet or product description sheet, with the original manufacturer’s sales/engineers point of contact name, telephone and address. The price quote must reference the manufacturer’s part number for the item quoted.

10. When requested, all vendors must submit a five foot long hose sample at vendor’s expense for destructive testing analysis.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically or pneumatically strength tested at 225 (+20,-0) PSI for ten minutes. Hose assembly manufacturer shall certify that each hose assembly is free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory strength test shall be provided with each shipped hose assembly.

4.HOSE 1-1/4" X 50' LPA 250PSI SMOOTH COVER HOSE COUPLED MALE X FEMALE HD BRASS CAMLOCKS SS COLLARS

A-2194-125250-050-CLS2&E-BR

Fully Coupled, Non Metallic Hose Assembly

1-1/4” I.D. by 50’ Long.

Model:

1. 1-1/4” Goodyear, Air & Multipurpose Hose, Wingfoot 250.


2. 1-1/4” Gates, Air and Multi-Purpose Hose, Premo Flex 3205R/3205B.


3. 1-1/4” Unisource Manufacturing, Air and Multi-Purpose Hose, 2194-125250-050.

Or Equal Criteria:

Hose, Nonmetallic, Nitrile Tube and Nitrile or Synthetic Rubber Outer Cover: Coupled and Fully Assembled.

1. Application: Low-pressure Air (LPA) services.


2. Working Pressure: 250 PSI Maximum.


3. Burst Pressure: 1,000 PSI Minimum.


4. Bend Radius: Minimum rated bend radius, 9 inches.


5. Rated Continuous Temperature: –20° F to +190° F.

Hose Construction:

1. Tube: Nitrile synthetic rubber. Must meet Rubber Manufactures Association (RMA) Class A standard for high oil resistance.


2. Cover: Nitrile or Synthetic rubber. To meet RMA Class B standards for medium-high oil resistance


3. Cover Color: Red (Black is acceptable). An all yellow outer cover is not acceptable.


4. Reinforcement: Spiral synthetic yarn.


5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories Distribution (NAHAD) certification standards.


6. Each hose assembly shall have the following components installed at each end:

•1st Hose End: 1-1/4" Female Cam & Groove x Hose Shank Coupler, Brass with Stainless Steel Cam Arms, Pins, Pull Rings and Passive Locking Device, PT Coupling Co., Part # 12CSLII, Item # 1290312L2.

• 2nd Hose End: 1-1/4" Male Cam & Groove x Hose Shank Adapter, Brass, PT Coupling Co., Part # 12E, Item # 1200512.

• End Fitting Interlocking Ferrules: End Fittings shall be coupled to the hose with PT Coupling Co., "ProGrip" C50SS Stainless Steel Crimp Ferrules. Ferrules to be size matched to the hose and end fittings. No "or equal" bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from US virgin brass with a machined finish IAW Commercial Item Description (CID) A-A-59326 and shall have a working pressure or 250 PSI or greater.

8. Branding / Markings: In addition to the manufacturer’s standard markings the hose is to be continuously Mylar or Stripe Branded / marked the following in 1/2” (minimum) lettering , which must be in a contrasting color or background to the outer cover of the hose. The lettering shall state as a minimum:

A. Standard Hose Brand Line/Model Number and Date of Manufacture.

B. “LP AIR” or “LOW PRESSURE AIR”

C. “250 PSI MAX WP”

D. “PSNS S/99”

9. All vendor price quotes or offers must include an original manufacturer’s cut sheet or product description sheet, with the original manufacturer’s sales/engineers point of contact name, telephone and address. The price quote must reference the manufacturer’s part number for the item quoted.

10. When requested, all vendors must submit a five foot long hose sample at vendor’s expense for destructive testing analysis.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically or pneumatically strength tested at 225 (+20,-0) PSI for ten minutes. Hose assembly manufacturer shall certify that each hose assembly is free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory strength test shall be provided with each shipped hose assembly.

5. 2" X 25' HOSE, NON METALLIC, SYNTHETIC RUBBER TUBE WITH COVER, COUPLED AND FULLY ASSEMBLED WITH PT COUPLING BRONZE CAM AND GROVE QD COUPLINGS A-2162-200-025-CLS2&E-BR

ITEM DESCRIPTION: LOW PRESSURE AIR HOSE ASSEMBLY

(2” ID X 25’ LONG)

MODEL:

1) Goodyear, Plicord Air Black 300, 549-368-064

2) Unisource Manufacturing, Series 2162-200 or 2168-200 Low Pressure Air

Or Equal Purchase Specification:

Hose, Nonmetallic, Synthetic Rubber Tube & Cover: Coupled and Fully Assembled with PT Coupling Co.,

Bronze, Cam & Groove Quick Disconnect Couplings.

Description:

1. Size: 2” I.D. by 25’ long.

2. Nominal OD: Not to exceed 2.67”

3. Application: Low Pressure Air (LPA).

4. Expected Working Pressure of Intended Services: 150 PSI.

5. Manufactured Rated Working Pressure: 250 PSI minimum.

6. Burst Pressure: 1,200 PSI, minimum.

7. Rated Bend Radius: 14 Inches minimum.

8. Rated Continuous Temperature: -20ºF to 180ºF.

9. No price quote or bid offer will be accepted without the vendor submitting: hose, fitting, and ferrule manufacturer

cut sheets or product description sheet attachments, which shall include as a minimum the technical characteristic

of the components and the manufacturer’s address, telephone number, fax number, and point of contact. The price

quote must reference the manufacture’s part numbers for the item quoted.

10. All quoting vendors if requested must submit a five foot long hose assembly to Shop 99 at vendor’s expense, for

destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

11. PSNS & IMF Engineering Code 260.5 must approve all exceptions and Or-Equal offers prior to purchase.

Construction:

12. Tube: Hose Inner Tube construction to be CR/SBR/Black synthetic rubber or blend. Hose inner tube must meet

Rubber Manufacturer’s Association (R.M.A.) Class B standard for medium oil resistance. Hose shall be wrapped or

mandrel type construction. Hose construction to be such that it maintains a round consistency when not pressurized

(i.e. No Lay Flat Hose).

13. Reinforcement: Multiple spiral-plied synthetic high tensile textiles.

14. Outer Cover: Wrapped finish with EPDM/SBR/Black synthetic rubber or blend. Hose must meet RMA Class C standards

for limited oil resistance.

15. Cover Color: Black, Green, or Blue. Yellow is not acceptable.

16. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories Distribution (NAHAD) certification standards.

17. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 2” Male Cam & Groove Quick Disconnect Adapter by Hose Shank, PT Coupling Co., Part # 20E,

Item # 1200520.

b. 2nd Hose End; Brass, 2” Female Cam & Groove Quick Disconnect Coupler by Hose Shank, with Stainless Steel, Cam Arms,

Pins, Pull Rings, and Passive Locking Device, PT Coupling Co., Part # 20CSLII, Item # 1290320L2.

c. End fittings shall be coupled to the hose with PT Coupling Co., Stainless Steel, “Pro-Grip" PART C50SS CRIMP FERRULE, sized to match the hose and fittings. No “or equal” hose clamps or bands will be accepted.

18. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar, or Stripe Branded, marked in ½”

lettering (minimum), which must be in a contrasting color to the background outer cover of the hose. The lettering

shall state as a minimum:

a. Manufacturer Name/Hose Brand/Line/Model Number, Flame Resistant, Date of Manufacture.

b. PSNS S/99 LP AIR

c. Manufactures rated WP (250 PSI MAX).

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 (+10,-0) PSIG for 10 minutes. Each certified hose to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date, and test pressure for each hose assembly.

6. 2" X 50' HOSE, NON METALLIC, SYNTHETIC RUBBER TUBE WITH COVER, COUPLED AND FULLY ASSEMBLED WITH PT COUPLING BRONZE CAM AND GROVE QD COUPLINGS A-2162-200-050-CLS2&E-BR

MODEL:

1) Continental ContiTech, Air Black 250 PSNS MSHA, SAP 20758845

2) Unisource Manufacturing, Series 2162-200 Low Pressure Air

Or Equal Purchase Specification:

Hose, Nonmetallic, Synthetic Rubber Tube & Cover: Coupled and Fully Assembled with PT Coupling Co.,

Bronze, Cam & Groove Quick Disconnect Couplings.

Description:

1. Size: 2” I.D. by 50’ long.

2. Nominal OD: Not to exceed 2.67”

3. Application: Low Pressure Air (LPA).

4. Expected Working Pressure of Intended Services: 150 PSI.

5. Manufactured Rated Working Pressure: 250 PSI minimum.

6. Burst Pressure: 1,200 PSI, minimum.

7. Rated Bend Radius: 14 Inches minimum.

8. Rated Continuous Temperature: -20ºF to 180ºF.

9. No price quote or bid offer will be accepted without the vendor submitting: hose, fitting, and ferrule manufacturer

cut sheets or product description sheet attachments, which shall include as a minimum the technical characteristic

of the components and the manufacturer’s address, telephone number, fax number, and point of contact. The price

quote must reference the manufacture’s part numbers for the item quoted.

10. All quoting vendors if requested must submit a five foot long hose assembly to Shop 99 at vendor’s expense, for

destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

11. PSNS & IMF Engineering Code 260.5 must approve all exceptions and Or-Equal offers prior to purchase.

Construction:

12. Tube: Hose Inner Tube construction to be CR/SBR/Black synthetic rubber or blend. Hose inner tube must meet

Rubber Manufacturer’s Association (R.M.A.) Class B standard for medium oil resistance. Hose shall be wrapped or

mandrel type construction. Hose construction to be such that it maintains a round consistency when not pressurized

(i.e. No Lay Flat Hose).

13. Reinforcement: Multiple spiral-plied synthetic high tensile textiles.

14. Outer Cover: Wrapped finish with EPDM/SBR/Black synthetic rubber or blend. Hose must meet RMA Class C standards

for limited oil resistance.

15. Cover Color: Black.

16. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories Distribution (NAHAD) certification standards.

17. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 2” Male Cam & Groove Quick Disconnect Adapter by Hose Shank, PT Coupling Co., Part # 20E,

Item # 1200520.

b. 2nd Hose End; Brass, 2” Female Cam & Groove Quick Disconnect Coupler by Hose Shank, with Stainless Steel, Cam Arms,

Pins, Pull Rings, and Passive Locking Device, PT Coupling Co., Part # 20CSLII, Item # 1290320L2.

c. End fittings shall be coupled to the hose with PT Coupling Co., Stainless Steel, “Pro-Grip" PART C50SS CRIMP FERRULE, sized to match the hose and fittings. No “or equal” hose clamps or bands will be accepted.

18. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar, or Stripe Branded, marked in ½”

lettering (minimum), which must be in a contrasting color to the background outer cover of the hose. The lettering

shall state as a minimum:

a. Manufacturer Name/Hose Brand/Line/Model Number, Flame Resistant, Date of Manufacture.

b. PSNS S/99 LP AIR

c. Manufactures rated WP (250 PSI MAX).

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 (+10,-0) PSIG for 10 minutes. Each certified hose to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date, and test pressure for each hose assembly.

7. 3" X 25' HOSE, NON METALLIC, SYNTHETIC RUBBER TUBE WITH COVER, COUPLED AND FULLY ASSEMBLED WITH PT COUPLING BRONZE CAM AND GROVE QD COUPLINGS A-2162-300-025-CLS2&E-BR

ITEM DESCRIPTION: LOW PRESSURE AIR HOSE ASSEMBLY

(3" I.D. X 25’ LONG)

MODEL:

1) Goodyear, Plicord Air Black 300, P/N 549-368-064

2) Unisource Manufacturing, Series 2162-300

Or- Equal Purchase Specification:

Hose, Nonmetallic, Synthetic Rubber Tube & Cover: Coupled and Fully Assembled, Low Pressure Air

Size: 3” I.D. by 25’ long.

Nominal OD: Not to exceed 3.625”

Weight: Maximum weight per foot not to exceed 2.15lbs.

Application: Low Pressure Air (LPA).

Working Pressure: 250 PSI, minimum.

Burst Pressure: 1,200 PSI, minimum.

Rated bend radius: 24 inches or less.

Rated Continuous Temperature: -20ºF to 180ºF

Construction:

Tube: Hose inner tube construction to be SBR synthetic rubber or blend. Hose inner tube must meet Rubber Manf. Assoc. (RMA Class B standard for medium oil resistance. Hose shall be wrapped or mandrel type construction. Hose construction to be such that it maintains a round consistency when not pressurized (e.g. No Lay Flat Hose)

Reinforcement: Multiple spiral-plied synthetic high tensile textiles.

Cover: Wrapped finish with SBR synthetic rubber. Hose must meet RMA Class C standards for limited oil resistance.

Cover Color: Black, Green or Blue. (Yellow is not acceptable)

Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories Distribution (NAHAD) certification standards.

Each hose assembly shall have the following components installed at each end:

1. 1st Hose End; Brass, 3” Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 30E, Item # 1200530.


2. 2nd Hose End; Brass, 3” Female Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, and Passive Locking Device, PT Coupling Co., Part # 30CSLII, Item # 1290330L2.


3. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with Stainless Steel, PT Coupling Co., “ProGrip" C50SS interlocking ferrules sized to match the hose and fittings. Must be interlocking ferrule type system, no “or equal” hose clamps accepted.

Branding/Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded, marked in ½” lettering (minimum), which must be in a contrasting color or background to the black outer cover of the hose.

The lettering shall state as a minimum:

a. Hose Brand/Line/Model number, Flame Resistant, Date of Manufacture.

b. PSNS S/99 LPA

c. 250 PSI MAX

All quoting vendors if requested must submit a five-foot long hose assembly at the vendor’s expense, for destructive testing analysis.

Hose Test & Assembly Certification:

After each hose assembly is completed it shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Manufacturer shall certify that hose assemblies are free of leaks, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are still properly positioned on the hose ends. Also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested (100% of hoses) shall be provided with shipped hoses.

1. 3" X 50' HOSE, NON METALLIC, SYNTHETIC RUBBER TUBE WITH COVER, COUPLED AND FULLY ASSEMBLED WITH PT COUPLING BRONZE CAM AND GROVE QD COUPLINGS A-2162-300-050-CLS2&E-BR

ITEM DESCRIPTION: LOW PRESSURE AIR HOSE ASSEMBLY

(3” ID X 50’ LONG)

MODEL:

1) Goodyear, Plicord Air Black 300, P/N 549-368-064

2) Unisource Manufacturing, Series 2162-300

Or- Equal Purchase Specification:

Hose, Nonmetallic, Synthetic Rubber Tube & Cover: Coupled and Fully Assembled, Low Pressure Air

Size: 3” I.D. by 50’ long.

Nominal OD: Not to exceed 3.625”

Weight: Maximum weight per foot not to exceed 2.15lbs.

Application: Low Pressure Air (LPA).

Working Pressure: 250 PSI, minimum.

Burst Pressure: 1,200 PSI, minimum.

Rated bend radius: 24 inches or less.

Rated Continuous Temperature: -20ºF to 180ºF

Construction:

Tube: Hose inner tube construction to be SBR synthetic rubber or blend. Hose inner tube must meet Rubber Manf. Assoc. (RMA Class B standard for medium oil resistance. Hose shall be wrapped or mandrel type construction. Hose construction to be such that it maintains a round consistency when not pressurized (e.g. No Lay Flat Hose)

Reinforcement: Multiple spiral-plied synthetic high tensile textiles.

Cover: Wrapped finish with SBR synthetic rubber. Hose must meet RMA Class C standards for limited oil resistance.

Cover Color: Black, Green or Blue. (Yellow is not acceptable)

Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories Distribution (NAHAD) certification standards.

Each hose assembly shall have the following components installed at each end:

1. 1st Hose End; Brass, 3” Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 30E, Item # 1200530G.


2. 2nd Hose End; Brass, 3” Female Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, and Passive Locking Device, PT Coupling Co., Part # 30CSLII, Item # 1290330L2G.


3. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with Stainless Steel, PT Coupling Co., “ProGrip" C50SS interlocking ferrules sized to match the hose and fittings. Must be interlocking ferrule type system, no “or equal” hose clamps accepted.

Branding/Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded, marked in ½” lettering (minimum), which must be in a contrasting color or background to the black outer cover of the hose.

The lettering shall state as a minimum:

a. Hose Brand/Line/Model number, Flame Resistant, Date of Manufacture.

b. PSNS S/99 LPA

c. 250 PSI MAX

All quoting vendors if requested must submit a five-foot long hose assembly at the vendor’s expense, for destructive testing analysis.

Hose Test & Assembly Certification:

After each hose assembly is completed it shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Manufacturer shall certify that hose assemblies are free of leaks, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are still properly positioned on the hose ends. Also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested (100% of hoses) shall be provided with shipped hoses.

A total quantity of 8 parts are required for this effort.

The results of this market research will contribute to determining the method of procurement. The applicable North American Industry Classification System (NAICS) code assigned to this procurement is 326220

THERE IS NO SOLICITATION AT THIS TIME. This request for capability information does not constitute a request for proposals; submission of any information in response to this market survey is purely voluntary; the government assumes no financial responsibility for any costs incurred.

If your organization has the potential capacity to provide these items, please provide the following information:

1. Organization name, address, email address, Web site address, telephone number, and size and type of ownership for the organization, including vendor CAGE code; and,


2. Tailored capability statements addressing the particulars of this effort, with appropriate documentation supporting claims of organizational and staff capability.

Responses are due in this office no later than 2:00 p.m. PST, MAY 9, 2024 Please send your capabilities statements and responses to this RFI via email directly to: jack.edwards@dla.mil

If you have any questions concerning this opportunity, please contact: jack.edwards@dla.mil

Attachments/Links